How to Apply Our Graphene Ceramic Spray Coating

Want mirror-like gloss and crazy water beading without pro install prices? This guide shows you how to apply Reflections Graphene Ceramic Spray Coating—a fast ceramic spray coating that delivers slick shine and 12+ months of protection—streak-free and beginner-friendly.

Shop the coating: https://reflectionsdetailing.co/products/graphene-ceramic-spray-coating

Table of contents

• Tools & products you’ll need

• Prep matters (most important step)

• Step-by-step application

• Cure time & layering

• After-care & maintenance

• Common mistakes (and easy fixes)

• FAQs

---

Tools & products you’ll need

• Reflections Graphene Ceramic Spray Coating (12 fl oz / 355 ml)

• 2–4 premium microfiber towels (edgeless, 300–400 GSM)

• pH-neutral car shampoo, wash bucket & mitt

• Clay bar or clay mitt + clay lube

• Panel-prep (IPA mix or dedicated paint prep)

• (Optional) light polish + pad for maximum clarity

Best conditions: Work in the shade on cool panels (50–80°F / 10–27°C) with low wind.

---

Prep matters (most important step)

1. Wash thoroughly. Remove dirt, film, and old toppers.

2. Decontaminate. Clay the paint to remove bonded contaminants.

3. (Optional but recommended) Polish light swirls for a glassy finish.

4. Panel-prep wipe. Use IPA/panel-prep to remove oils so the coating bonds cleanly.

Skipping prep is the #1 reason coatings don’t last. Spend time here—it pays off.

---

Step-by-step application

Tip: Use one towel to apply and a second clean towel to buff. Swap towels if they get saturated.

1. Shake well. Activate the graphene + ceramic resins.

2. Prime your towel. Spray 2–3 light mists onto a microfiber towel (not directly on the panel).

3. Apply panel-by-panel. Wipe in straight, overlapping passes. Thin, even coverage is best.

4. Allow to flash (1–2 minutes). You may see a faint rainbow/sheen as solvents evaporate.

5. Level & buff. With a clean towel, wipe until the panel looks crystal clear and slick.

6. Repeat around the vehicle. Roof → glass → hood → fenders → doors → trunk → bumpers → wheels & trim.

Safety: Contains graphene, silicones, and solvent. Use in a ventilated area; avoid ingestion/skin contact.

---

Cure time & layering

• Initial cure: Keep dry for 4–6 hours.

• Full cure: ~24 hours. Avoid soaps during this window.

• Layering: Apply 1–3 coats. Wait ~60 minutes between coats to stack protection.

• Glass/trim: Apply lightly and buff thoroughly to prevent haze.

---

After-care & maintenance

• First 7 days: Avoid strong detergents or toppers.

• Regular wash: pH-neutral shampoo, soft mitt, thorough rinse.

• Drying: Plush towel or filtered air—watch the water sheet off.

• Boost (optional): A silica detailer every 4–6 weeks keeps slickness maxed.

• When to re-apply: If water no longer beads/sheets like day one, re-coat a clean panel.

---

Common mistakes (and easy fixes)

• Streaks/high spots: Over-applied or waited too long. Re-mist a little product and immediately buff clear.

• Grabby towel: Towel is saturated—switch to a fresh microfiber.

• Haze on glass: Use fewer sprays and buff more; glass shows excess easily.

• Poor durability: Usually prep-related. Next time, include a panel-prep wipe after polishing.

---

Real-world results

• Before/after: Half-hood coated vs. uncoated—deeper gloss & darker reflections.

• Hydrophobic test: Short video of water beading/sheeting after application.

Ready to coat?
👉 Shop Reflections Graphene Ceramic Spray Coating
https://reflectionsdetailing.co/products/graphene-ceramic-spray-coating

---

FAQs

How long does it last?
Up to 12+ months per application, depending on climate and wash routine.

Is it beginner-friendly?
Yes—thin application and prompt buffing make it very forgiving.

Do I need to polish first?
Not required, but polishing increases clarity and depth of gloss.

Is it safe on paint, glass, wheels, and trim?
Yes—apply lightly and buff well, especially on glass and textured trim.